how to install railing on outside stairs

How to Install Exterior Stairway Railings | Home Guides ...

Exterior stairway railings made from wood, wrought iron or aluminum must be installed to provide safety for those using the stairs. With wood railings, posts are notched to bolt against the sides ...【Get Price】

How to Install a Stair Handrail | This Old House

9. Cut handrail to length, mitering the ends to 45 degrees. 10. Glue and nail a mitered return to each end of the handrail. 11. Prime and paint, or stain and/or varnish the handrail. 12. Once dry, screw handrail to mounting brackets.【Get Price】

How to Install Railings in Concrete for Safer, More ...

To install railings in concrete, a wedge anchor about ⅜ inch in diameter and three inches long is the approximate standard. Before you start, you’ll first need to drill holes for the anchors. To mark where you’re going to drill, it’s helpful to measure out your post spacing, place the posts, and mark through the holes that are already drilled in the post base.【Get Price】

How to Install Stair Railing - The Spruce

Note: We are installing stair railing only--railing attaches to a wall in a stairwell. For an entire railing/baluster/newel package, see our article about Staircase and Balcony Railing Kits . Continue to 2 of 11 below.【Get Price】

Install a New Stair Handrail | The Family Handyman

With the stair railing mounted, it’s easy to measure for and install the short pieces that return to the wall at the top and bottom of the rail (Photo 13). Measure from the long point of the 45-degree miter on the rail to the wall and add about 1/16 in. for a tight fit. Then cut the returns on your power miter saw.【Get Price】

How to Install a Metal Railing | This Old House

Use a marker to trace around the edges of the railing. 3. Use the coring drill to drill out holes for the railing. A scrap piece of stone can be used to guide the drill. 4. Use the masonry drill to clean out the hole made by the coring drill. 5. Dry fit the railings to ensure a correct fit. 6.【Get Price】

How to Install a Wood Handrail for Exterior Front Stairs ...

How to Install a Wood Handrail for Exterior Front Stairs Wooden handrails for exterior stairs provide balance and support when going up and down the stairs, and set off the front stairway.【Get Price】

How to Install a Stair Handrail | This Old House

3. Calculate height of handrail and mounting brackets; mark bracket height on level. 4. Use level to mark bracket height on wall at top and bottom of staircase. 5. Snap chalk line to connect the two wall marks. 6. Using electronic stud finder, mark wall studs at top, middle and bottom of staircase. 7.【Get Price】

How to Install Stair Railing - The Spruce

Municipalities' requirements may vary, but staircase code tends to dictate that railing is 34" to 38" high, as measured from the nose of the stair tread directly upward to the top of the railing. The nose is the very outer projection of the stair tread.【Get Price】

Install a New Stair Handrail | The Family Handyman

Position and install two brackets first, one close to the top and one close to the bottom of the stair railing. Photo 9 shows how to locate the exact center of the studs. This is an important step because the rail brackets must be centered on the stud or one of the two top screws will miss the framing.【Get Price】

How to Install Stair Railing - The Spruce

Note: We are installing stair railing only--railing attaches to a wall in a stairwell. For an entire railing/baluster/newel package, see our article about Staircase and Balcony Railing Kits.【Get Price】

How to Install New Stair Treads and Railings | how-tos | DIY

These basic step-by-step instructions demonstrate how to install a stairway handrail for added safety. How to Paint and Install Balusters The DIY to the Rescue crew demonstrates how to replace 100 existing balusters with 200 freshly painted balusters spaced closer together.【Get Price】